Molecular recognition and sensing can be coupled to interfacial capacitance changes on graphene foam surfaces linked to double layer effects and coupled to enhanced quantum capacitance. 3D graphene foam film electrodes (Gii-Sens; thickness approximately 40 µm; roughness factor approximately 100) immersed in aqueous buffer media exhibit an order of magnitude jump in electrochemical capacitance upon adsorption of a charged molecular receptor based on pyrene-appended boronic acids (here, 4-borono-1-(pyren-2-ylmethyl)pyridin-1-ium bromide, or abbreviated T1). This pyrene-appended pyridinium boronic acid receptor is employed here as a molecular receptor for lactate. In the presence of lactate and at pH 4.0 (after pH optimization), the electrochemical capacitance (determined by impedance spectroscopy) doubles again. Lactic acid binding is expressed with a Hillian binding constant (Klactate = 75 mol-1 dm3 and α = 0.8 in aqueous buffer, Klactate = 460 mol-1 dm3 and α = 0.8 in artificial sweat, and Klactate = 340 mol-1 dm3 and α = 0.65 in human serum). The result is a selective molecular probe response for lactic acid with LoD = 1.3, 1.4, and 1.8 mM in aqueous buffer media (pH 4.0), in artificial sweat (adjusted to pH 4.7), and in human serum (pH adjusted to 4.0), respectively. The role of the pyrene-appended boronic acid is discussed based on the double layer structure and quantum capacitance changes. In the future, this new type of molecular capacitance sensor could provide selective enzyme-free analysis without analyte consumption for a wider range of analytes and complex environments.
Graphite , Lactic Acid , Humans , Lactic Acid/analysis , Graphite/chemistry , Boronic Acids/chemistry , Sweat/chemistry , Electrodes
Ionic diode based devices or circuits can be applied, for example, in electroosmotic pumps or in desalination processes. Aquivion ionomer coated asymmetrically over a Teflon film (5 µm thickness) with a laser-drilled microhole (approximately 10 µm diameter) gives a cationic diode with a rectification ratio of typically 10-20 (measured in 0.01 M NaCl with ±0.3 V applied bias). Steady state voltammetry, chronoamperometry, and electrochemical impedance spectroscopy data are employed to characterize the ionic diode performance parameters. Next, a COMSOL 6.0 finite element model is employed to quantitatively assess/compare transient phenomena and to extract mechanistic information by comparison with experimental data. The experimental diode time constant and diode switching process associated with a distorted semicircle (with a typical diode switching frequency of 10 Hz) in the Nyquist plot are reproduced by computer simulation and rationalized in terms of microhole diffusion-migration times. Fundamental understanding and modeling of the ionic diode switching process can be exploited in the rational/optimized design of new improved devices.
Molecularly rigid polymers with internal charges (positive charges induced by amine methylation) allow electroosmotic water flow to be tuned by adjusting the charge density (the degree of methylation). Here, a microporous polyamine (PIM-EA-TB) is methylated to give a molecularly rigid anion conductor. The electroosmotic drag coefficient (the number of water molecules transported per anion) is shown to increase with a lower degree of methylation. Net water transport (without charge flow) in a coupled anionic diode circuit is demonstrated based on combining low and high electroosmotic drag coefficient materials. The AC-electricity-driven net process offers water transport (or transport of other neutral species, e.g., drugs) with net zero ion transport and without driver electrode side reactions.
A blue light mediated photochemical process using solid graphitic carbon nitride (g-C3N4) in ambient air/isopropanol vapour is suggested to be linked to "nanophase" water inclusions and is shown to produce approx. 50 µmol H2O2 per gram of g-C3N4, which can be stored in the solid g-C3N4 for later release for applications, for example, in disinfection or anti-bacterial surfaces.
Graphitic carbon nitride (g-C3N4) is known to photogenerate hydrogen peroxide in the presence of hole quenchers in aqueous environments. Here, the g-C3N4 photocatalyst is embedded into a host polymer of intrinsic microporosity (PIM-1) to provide recoverable heterogenized photocatalysts without loss of activity. Different types of g-C3N4 (including Pt@g-C3N4, Pd@g-C3N4, and Au@g-C3N4) and different quenchers are investigated. Exploratory experiments yield data that suggest binding of the quencher either (i) directly by adsorption onto the g-C3N4 (as shown for α-glucose) or (ii) indirectly by absorption into the microporous polymer host environment (as shown for Triton X-100) enhances the overall photochemical H2O2 production process. The amphiphilic molecule Triton X-100 is shown to interact only weakly with g-C3N4 but strongly with PIM-1, resulting in accumulation and enhanced H2O2 production due to the microporous polymer host.
The concept of a reversible polymer displacement sensor mechanism for electrochemical glucose monitoring is demonstrated. A pyrene-derivatised boronic acid chemo-receptor for glucose is adsorbed onto a graphene foam electrode. Spontaneous oxidative polymerisation of nordihydroguaiaretic acid (NHG) onto the graphene foam electrode leads to a redox active film (poly-NHG) covalently attached to the boronic acid receptors. Oxidation of poly-NHG frees the boronic acid receptors to interact with glucose from the solution phase, which is detected due to competitive binding when reduced poly-NHG re-binds to the boronic acid functional groups. The sensor shows the anticipated boronic acid selectivity of fructose > glucose. The ratio of charges under the voltammetric peaks for poly-NHG unbound and bound is employed for glucose sensing with an approximately linear analytical range from 1 to 50 mM glucose in aqueous pH 7 buffer. The new methodology is shown to give apparent saccharide - boronic acid binding constants and to work in human serum. Therefore, in the future it could be developed further for glucose monitoring.
Graphite , Blood Glucose , Blood Glucose Self-Monitoring , Boronic Acids , Glucose , Humans , Masoprocol , Polymers
This study examines the role of defects in structure-property relationships in spinel LiMn1.5Ni0.5O4 (LMNO) cathode materials, especially in terms of Mn3+ content, degree of disorder, and impurity phase, without the use of the traditional high-temperature annealing (≥700 °C used for making disordered LMNO). Two different phases of LMNO (i.e., highly P4332-ordered and highly Fd3Ì m-disordered) have been prepared from two different ß-MnO2-δ precursors obtained from an argon-rich atmosphere (ß-MnO2-δ (Ar)) and a hydrogen-rich atmosphere [ß-MnO2-δ (H2)]. The LMNO samples and their corresponding ß-MnO2-δ precursors are thoroughly characterized using different techniques including high-resolution transmission electron microscopy, field-emission scanning electron microscopy, Raman spectroscopy, powder neutron diffraction, X-ray photoelectron spectroscopy, synchrotron X-ray diffraction, X-ray absorption near-edge spectroscopy, and electrochemistry. LMNO from ß-MnO2-δ (H2) exhibits higher defects (oxygen vacancy content) than the one from the ß-MnO2-δ (Ar). For the first time, defective ß-MnO2-δ has been adopted as precursors for LMNO cathode materials with controlled oxygen vacancy, disordered phase, Mn3+ content, and impurity contents without the need for conventional methods of doping with metal ions, high synthetic temperature, use of organic compounds, postannealing, microwave, or modification of the temperature-cooling profiles. The results show that the oxygen vacancy changes concurrently with the degree of disorder and Mn3+ content, and the best electrochemical performance is only obtained at 850 °C for LMNO-(Ar). The findings in this work present unique opportunities that allow the use of ß-MnO2-δ as viable precursors for manipulating the structure-property relationships in LMNO spinel materials for potential development of high-performance high-voltage lithium-ion batteries.
Bacteriophage material (M13, wild-type) deposited as a film onto a poly(ethylene terephthalate) (PET) substrate (6 µm thick with a 20 µm diameter laser-drilled microhole) has been investigated for ion conductivity and ionic current rectification effects for potential applications in membranes. The M13 aggregate membrane forms under acidic conditions (in aqueous 10 mM acids) and behaves like a microporous anion conductor with micropores defined by the packing of cylindrical virus particles. Asymmetric deposition on the PET film substrate in conjunction with semipermeability leads to anionic diode behavior. Typical rectification ratio values are around 10 (determined at ±1 V) in aqueous 10 mM acids. Cationic guest species (aqueous Cu2+, Co2+, Ag+) consistently lead to a rectification minimum at 0.5 mM guest concentration. In contrast, anionic guest species (indigo carmine) lead to a similar rectification minimum already at 5 µM concentration. The behavior is proposed to be associated with cation exclusion effects on transport.
Titanate nanosheets (single layer, typically 200â¯nm lateral size) deposited from aqueous colloidal solution onto electrode surfaces form lamellar hosts that bind redox active molecular redox probes. Here, hydrophobic redox systems such as anthraquinone, 1-amino-anthraquinone, deca-methylferrocene, 5,10,15,20-tetraphenyl-21H,23H-porphine manganese (III) chloride (TPPMnCl), and α-tocopherol are shown to bind directly from cyclopentanone solution (and from other types of organic solvents) into the titanate nanosheet film. For anthraquinone derivatives, stable voltammetric responses are observed in aqueous media consistent with 2-electron 2-proton reduction, however, independent of the pH of the outside solution phase environments. For decamethylferrocene a gradual decay of the voltammetric response is observed, but for TPPMnCl a more stable voltammetric signal is seen when immersed in chloride containing (NaCl) electrolyte. α-Tocopherol exhibits chemically irreversible oxidation and is detected with 1â¯mM-20â¯mM linear range and approximately 10-3â¯M concentration limit of detection. All redox processes exhibit an increase in current with increasing titanate film thickness and with increasing external electrolyte concentration. This and other observations suggest that important factors are analyte concentration and mobility within the titanate host, as well as ion exchange between titanate nanosheets and the outside electrolyte phase to maintain electroneutrality during voltammetric experiments. The lamellar titanate (with embedded tetrabutyl-ammonium cations) behaves like a hydrophobic host (for hydrophobic redox systems) similar to hydrophobic organic microphase systems. Potential for analytical applications is discussed.
This paper describes the development of a portable, automated flow injection-chemiluminescence (FI-CL) analyzer incorporating on-line solid-phase extraction (SPE) for the determination of dodecylamine (detergent) in diesel fuels. The method is based on the peroxyoxalate/sulforhodamine 101 chemiluminescence reaction, with SPE required to remove indigenous compounds within the diesel fuel matrix that interfere with the CL response. The automated analyzer achieved a detection limit of 2.9 mg L(-1) and a linear range of 2.9-50 mg L(-1), which was suitable for determinations of dodecylamine at levels typically present in fully formulated diesel fuels (40 mg L(-1)). Analyses of base fuels from five different sources demonstrated that an automated FI-CL-SPE system could provide a portable instrument for monitoring the presence/absence of dodecylamine in diesel fuels.
